Tekmar Adhesives Tekmar Formula TS-3 Premium Screen Print Ink Remover, 1 gal TEK-TS-3-1G
Quick answer: Formula TS-3 is Tekmar's plastisol spot remover: the maker says it takes out virtually all cured plastisol, most water-based, catalyst, nylon and puff inks, and most transfer adhesives. Non-flammable and made to be sprayed through a Target spot gun.
Sizes and options
1 gal 5 gal (2 x 2.5 gal) 55 gal drum
Specs
| Tekmar item # | TS3-4G |
|---|---|
| Size / option | 1 gal |
| Type | Non-flammable, fast-drying ink spot remover (Tekmar) |
| Removes | Cured plastisol (virtually 100% per Tekmar); most water-based, catalyst, nylon and puff inks; most transfer and heat-transfer adhesives; grease and oil |
| Main ingredient (SDS) | Methylene chloride 70 to under 90% |
| Flash point (SDS) | Over 212 F (Tag closed cup) |
| Specific gravity / VOC (TDS) | 1.257 / 240 g/l |
| HMIS / NFPA (TDS) | H2 F1 R0 / H2 F1 R0 |
| Shipping (Tekmar) | 1 gal and smaller: Limited Quantity, ground. 2.5, 5 and 55 gal: UN2810, 6.1, PG III |
| Maker sizes | 1 gal (4 x 1 gal case), 5 gal (2 x 2.5 gal), 55 gal drum |
How to use
- Make sure plastisol is fully cured before spotting it, or it will smear.
- Fill the gun 4/5 full and prime it.
- Over an exhaust station, hold the gun about 6 in away and circle the spot from the outside in until it flushes through.
- Feather the edge with a wide spray and dry fast with the exhauster or air dryer.
Safety and shipping
- Prop 65 (from the SDS): WARNING, contains methylene chloride, known to the State of California to cause cancer.
- OSHA methylene chloride standard: workplace limits of 25 ppm (8-hour average) and 125 ppm (15-minute); use an exhaust station or good ventilation.
- Wear goggles and gloves. Read the SDS.
- Shipping: ships from Tekmar's Santa Barbara, CA location; 1 gal and smaller Limited Quantity ground; 2.5/5/55 gal Class 6.1 UN2810 PG III hazmat ground.
Downloads
- Formula TS-3 technical data (PDF)
- Formula TS-3 safety data sheet (05-01-2024) (PDF)
- Formula TS-3 hoja de seguridad (PDF)
- New Gen cleaning fluids tech data (PDF)
- Cheat sheet: Tekmar spot fluids safety and shipping (PDF)
- Cheat sheet: Tekmar spot cleaning fluids and guns (existing) (PDF)
Video: Tekmar Spot Cleaning 101
FAQ
Will TS-3 remove cured plastisol?
Yes. Tekmar says TS-3 removes virtually 100% of cured plastisol, plus most water-based, catalyst, nylon and puff inks.
Should the ink be cured before I spot it?
For plastisol, yes: Tekmar says spot only fully cured ink, or it runs and spreads.
Is TS-3 flammable?
No. The SDS gives a flash point over 212 F and Tekmar calls it non-flammable.
Does TS-3 contain methylene chloride?
Yes, 70 to under 90% per the SDS, so it carries a Prop 65 cancer warning and OSHA exposure rules apply.
TS-3 or TS-5?
TS-3 is Tekmar's methylene chloride plastisol remover; TS-5 is the New Gen option with no methylene chloride or n-propyl bromide.
Goes with
- Tekmar Formula TS-5 Spot Cleaning Fluid, 1 gal
- Tekmar Formula DT-1000 DTG and DTF Spot Remover, 1 gal
- Target TG300 PRO Spot Cleaning Gun 110V 60 Hz
- Target Exhaustex 1500 Table Top Spot Cleaning Station 110V 60 Hz
- Tekmar TS-3 vs TS-5 vs DT-1000 spot cleaner
- how to remove plastisol ink spots from shirts
Why Buckets of Ink
We carry Tekmar spot cleaning, pallet adhesive and press-side products for screen printers, with real answers from our Tempe, Arizona team. Questions on fluids, guns or parts: call 480-229-7806.
Tekmar Formula TS-3 Premium Screen Print Ink Remover, 1 gal
Price
Color
Quantity
minimum quantity: x available in bundles of: x Product ordered in bundles.
More Images
Shipping
bucketsofink has a highly developed production and shipping system and we make every effort to ship your order in a fast and effecient manner.



