Tekmar Spot Gun Troubleshooting: Spitting, Leaks and Rings

Buckets of InkFree Tool · Tekmar Spot Gun Troubleshooting

Home › Tekmar › Tekmar Spot Gun Troubleshooting

Quick answer: most Tekmar spot gun problems come from the nozzle, priming or drying. Clean or replace the TG1 nozzle when the spray spits, fill the bottle 4/5 full and prime it, run PRO guns 15 seconds on and 15 off, and dry the spot fast to stop rings. Never put flammable or water-based fluid in the gun.

Problem, cause, fix

ProblemLikely causeFix (from Tekmar's manuals)
Spray spits or is unevenClogged or worn TG1 nozzleRemove the nozzle head (keep both washers), tap it on a hard surface or push a copper strand through. Never a pin or needle. Replace the TG1 if worn. Shop part
Nozzle leaksBrass one-way washer reversed or head looseRefit the washer with its small shoulder facing forward and tighten the head against the collar. Shop part
No spray after fillingGun not primedFill the bottle about 4/5 full and squeeze the trigger until fluid shoots from the nozzle.
Weak or too strong spray (TG300 PRO / TG350 PRO)Volume knob movedTurn the rear knob counter-clockwise to the stop, then clockwise 2 1/2 turns (Tekmar PRO sheets).
Gun gets hotRunning too longPRO guns are intermittent duty: spray 15 seconds on, 15 seconds off.
Ring around the cleaned spotEdge dried slowlySpray wide around the wet edge to feather it, then dry fast with an exhaust station, the TurboAir lever or air dryer. Never use the dryer. Shop part
TG200 noisy or roughNeeds oilPut a few drops of sewing machine or 3-in-1 oil in the oil port weekly (MK II manual).
TG350 air dryer damagedAir pressure too highPre-2021 TG350: keep the air line at or below 80 psi with a regulator.
Gun will not runWorn switch, coil motor or armature, or cord damageCheck the cord first; do not repair a damaged cord yourself. Replace the worn part or call Tekmar for an RMA (805-965-0704). Shop part
Exhaustex lost suctionBlocked hose or lint in blowerClear the hose; de-lint the blower every 6 to 12 months. Check the fuse.
Exhaustex 2000 smells of solventCharcoal is spentChange the charcoal after about 10 to 15 gallons of fluid. Shop part
TB-591 leaks glue at the needleLoose or worn packingTighten packing screw 591-41 in 1/8 turn steps; if it still leaks, replace packing 591-40. Shop part
TB-591 leaks at the fluid nozzleDried glue or worn nozzle and needleClean fluid nozzle 591-03; if it still leaks replace nozzle and needle as a set. Shop part
Safety: Tekmar spot guns are high-pressure airless guns. Never aim at skin or eyes, wear goggles and gloves, and plug into an outlet that matches the gun voltage. Formula TS-Special and any flammable liquid must NOT be used in a Tekmar TG gun.

Care that prevents most problems

  • Empty the bottle before overnight storage (PRO guns).
  • Older TG100, TG125 and TG150: drain, then run a few seconds of light machine oil before storing.
  • TG200 MK II: oil the port weekly.
  • Keep a spare Target TG1 Adjustable Nozzle on the bench.

Downloads and tools

FAQ

Why does my Tekmar spot gun spit?

Usually a clogged or worn TG1 nozzle. Clean it with a copper strand, never a pin, or replace it.

Why does my spot gun leave a ring?

The wet edge dried slowly. Feather it with a wide spray and dry fast with an exhauster or air dryer; never put the shirt back in the dryer.

How long can I run a TG300 PRO or TG350 PRO?

Tekmar says intermittent use: 15 seconds on, 15 seconds off.

Can I use water or a flammable cleaner in my gun?

No. Tekmar's manuals ban water-based and flammable fluids; they void the warranty and flammables are a fire risk.

How do I get warranty repair?

Call Tekmar at 805-965-0704 or email service@tekmarltd.com for an RMA before you ship the gun.

Still stuck? Talk to a real screen printer: 480-229-7806
Buckets of Ink, 906 S Priest Dr, Suite 101, Tempe, AZ 85281. Same-day pickup, Phoenix-metro delivery and fast shipping.
Ask a questionAsk about our discountsCall 480-229-7806
Built by Buckets of Ink, Tempe, Arizona · Questions? Call 480-229-7806
Search
Your cart is empty
Search