Ulano Emulsion Stencil Remover Liquid No. 4 Gallon GSRL4
Ulano Corporation Stencil Remover Liquid No. 4 Gallon: what it is
A ready-to-use liquid stencil remover that strips direct emulsion, CDF capillary film and Pulsar film from any mesh, including metalized polyester. It will not etch mesh and has no strong alkalis or bleach (hypochlorite). Good for dip tanks too.
Best for: Reclaiming direct emulsion stencils; Removing CDF capillary direct films and Pulsar indirect film; Dip tanks (no heating needed; safe on frame adhesives).
How to use Stencil Remover Liquid No. 4
- Remove ink with the correct solvent.
- Use Screen Degreaser Liquid No. 3 to clear solvent residue, then rinse well.
- Brush No. 4 onto both sides with a soft brush.
- Wait 5 minutes, no longer. Never let it dry on the screen or the stencil can become permanent.
- Blast the stencil off with a hard water spray, ideally a pressure washer.
- Tank use: may be diluted with water no more than 1:2, only after testing; full strength gives the fastest removal.
Ulano Corporation Stencil Remover Liquid No. 4 Gallon specifications
| Size | Gallon |
| Part # | GSRL4 |
| Type | Ready-to-use liquid stencil remover |
| Mix ratio | Use full strength; tanks up to 1:2 with water after testing |
| Dwell time | 5 minutes maximum |
| Removes | Direct emulsions, CDF Direct-Films, Pulsar |
| Works on | All mesh incl. metalized polyester; will not etch mesh |
| Contains | No strong alkalis or hypochlorites; a strong oxidant |
| Maker sizes | Quart (QSRL4), gallon (GSRL4), 5 gal (5GSRL4), 50 gal (50GSRL4) |
Stencil Remover Liquid No. 4 safety summary
- Hazards: Strong oxidant; can irritate skin (per Ulano TDS/web page; SDS not public)
- Protection: Gloves (Ulano); eye protection advised
- Storage: Keep container tightly closed; clean spills at once
Stencil Remover Liquid No. 4 downloads (SDS, TDS, instructions)
Works with Stencil Remover Liquid No. 4
- Ulano QX-5 Ultra-Fast-Exposing SBQ-Photopolymer Emulsion Gal
- Green Extra Heavy Blockout No. 10 QT
- Blue Biggie Scrub Pad
Stencil Remover Liquid No. 4 FAQ
How long do I leave Ulano Stencil Remover No. 4 on the screen?
Five minutes, no longer. Do not let it dry or the stencil can lock in permanently.
Do I need to dilute Ulano No. 4 stencil remover?
No, it is ready to use. In a tank you may dilute up to 1:2 with water after testing, but Ulano recommends full strength.
Will Ulano No. 4 damage my mesh?
No. It does not etch mesh and is safe on metalized polyester.
What does Ulano No. 4 remove?
Direct emulsions, CDF capillary films and Pulsar indirect film.
Stencil Remover Liquid No. 4 Gallon
Ready-to-use stencil liquid remover for fast and thorough removal of direct emulsions, CDF Direct-Films, and Pulsar indirect film from all types of mesh including metalized polyester.
Will not etch mesh; contains no strong alkalis or hypochlorites. Ideal for use in tanks: will not attack adhesives on stretch and glue frames; tank heating unnecessary. Odor free
- Instructions
- Remove ink with the proper solvent.
- Use Screen Degreaser Liquid No. 3 to remove solvent residues and to help speed the action of the stencil remover. Rinse thoroughly.
- Use a soft brush to apply Stencil Remover Liquid No. 4 on the screen from both sides.
- Wait five minutes - no longer. Do not allow the stencil remover to dry on the screen, as this can result in a permanent stencil.
- Wash away the stencil with a hard spray of water, preferably a power spray.
- Tank method: Dilute Stencil Remover No. 4 with water (no more than 1:2) - but only after thorough testing. It is recommended, however, that Ulano No. 4 be used at full strength for fastest and most thorough stencil removal.
Stencil Remover Liquid No. 4 is a strong oxidant. It can cause skin irritation; use gloves. Keep the container closed tightly. Clean spills immediately.
Emulsion Remover
First Aid: In case of contact with the eyes or skin, flush immediately with water. If irritation develops, contact a physician.
Ulano Liquid Emulsion Remover
Maker document (Ulano): Ulano Stencil Remover Liquid No. 4 tech data sheet
Stencil Remover Liquid No. 4: questions
What does Stencil Remover Liquid No. 4 remove?
Direct emulsions, CDF direct films and Pulsar indirect film, from all mesh types including metalized polyester.
Will it damage my mesh or frames?
Stencil Remover Liquid No. 4 Gallon
Price
Color
Size
Quantity
minimum quantity: x available in bundles of: x Product ordered in bundles.
Shipping
bucketsofink has a highly developed production and shipping system and we make every effort to ship your order in a fast and effecient manner.






