Ulano Emulsion Ulano QX-5 Ultra-Fast-Exposing SBQ-Photopolymer Emulsion Gal 1GUFQX-5BLUE
Ulano Corporation QX-5 Blue Ultra-Fast-Exposing SBQ-Photopolymer Emulsion Gallon: what it is
A blue, ready-to-use, ultra-fast-exposing SBQ photopolymer direct emulsion. Nothing to mix. High viscosity and 41% solids give easy coating, good bridging on coarse mesh and fast drying. Resists plastisol, most washup solvents and some water-based inks.
Best for: High-volume shops that want fast coating, drying and exposure; Weak light sources (fluorescent tubes); Plastisol and solvent-based inks.
How to use QX-5 Blue Ultra-Fast-Exposing SBQ-Photopolymer Emulsion
- Degrease (Magic Mesh Prep, Degreaser No. 3, or degreaser concentrate 1:20) and rinse; optionally abrade new mesh first.
- No sensitizer: QX-5 is presensitized. Handle under yellow safelight only.
- Method 1: one coat on the print side, then one on the squeegee side; dry.
- Method 2: two coats print side, then two coats squeegee side, wet-on-wet, turning the screen 180 degrees after each coat.
- Method 3: do Method 2, dry, then add two more print-side coats wet-on-wet (smoother print edge).
- Dry flat, print side down, at room temperature in a clean area (fan helps); a dryer with filtered air up to 104 F (40 C) is fine.
- Work out a starting time from the base exposure table, then fine-tune with a step-wedge test or exposure calculator: best exposure is when the squeegee side is hard (not slimy) and the colour stops darkening.
- Wash out: wet both sides with a gentle cold spray, then spray hard from the print side until the image clears; rinse until no soft emulsion or foam is left; blot or vacuum dry.
- Blockout: use leftover emulsion before exposure, or (non-water inks) No. 10 / Screen Filler No. 60 after.
- Reclaim: remove ink, use Screen Degreaser No. 3, brush on Stencil Remover Liquid No. 4 both sides (do not let it dry), then power-wash.
Ulano Corporation QX-5 Blue Ultra-Fast-Exposing SBQ-Photopolymer Emulsion Gallon specifications
| Size | Gallon |
| Part # | 1GUFQX-5BLUE |
| Type | SBQ photopolymer (Ulano spec box: SBQ, non-diazo dual cure) |
| Solids | 41% |
| Viscosity | 5,000 cps |
| Sensitizer | None (presensitized) |
| Inks | Plastisol, most solvent-based inks; some water-based |
| Humidity | Will not go tacky in high humidity |
| Base exposure (305 white mesh, 40 in, method 1/2/3) | Metal halide 5 kW: 4/12/16 s; 3 kW: 7/20/26 s; 1 kW: 22/60/82 s; 40 W fluorescent: 72/180/300 s |
| Exposure factors | Dyed mesh x1.5-2.0; finer than 330 x0.7-0.9; coarser than 250 x1.1-2.0; high heat/humidity x1.3-1.8 |
| Shelf life | Unopened 1 year at 70 F (21 C) |
| Maker sizes | 28 oz, 1 gal, 5 gal, 50 gal |
QX-5 Blue Ultra-Fast-Exposing SBQ-Photopolymer Emulsion safety summary
- Storage: Unopened 1 year at 70 F (21 C); handle under yellow safelight
QX-5 Blue Ultra-Fast-Exposing SBQ-Photopolymer Emulsion downloads (SDS, TDS, instructions)
- Ulano Corporation Tech Data Sheet QX-5 Blue (Ulano, code 311dm)
- Ulano Corporation Product Fact Sheet QX-5 Blue (Ulano, 311dm)
- Ulano Corporation Ulano Emulsion Brochure (selection chart)
Making a direct emulsion stencil (Ulano) video
Works with QX-5 Blue Ultra-Fast-Exposing SBQ-Photopolymer Emulsion
QX-5 Blue Ultra-Fast-Exposing SBQ-Photopolymer Emulsion FAQ
Do I need to add diazo to Ulano QX-5?
No. QX-5 Blue is fully presensitized; use it straight from the container under yellow light.
What is the exposure time for Ulano QX-5 Blue?
On 305 white mesh at 40 in, Ulano's base is about 12 s with a 5 kW metal halide (2+2 coats), or 180 s under 40 W fluorescent tubes. Confirm with a step-wedge test.
Does Ulano QX-5 work with water-based ink?
Only some water-based inks. It is made for plastisol and solvent inks.
What size is the small Ulano QX-5?
Ulano packs QX-5 in 28 oz (0.83 L), 1, 5 and 50 gallon units; there is no true quart.
Qx-5 Photo-Polymer Emulsion
QX-5 Red and QX-5 Blue are universal, ready-to-use, ultra-fast-exposing SBQ-photopolymer direct emulsions. Their high viscosity (5000 centipose) provides good coating control. Their high solids content (41%) results in better mesh bridging on coarse mesh and fast drying. Their high contrast colors afford easy stencil inspection. Ulano QX-5 emulsion Red and QX-5 Blue are resistant to plastisol inks, washup solvents, and water-based inks, making them easy to reclaim in automatic stencil removal equipment or by hand.
Emulsion
Ulano QX-5 Ultra-Fast-Exposing SBQ-Photopolymer Emulsion Gal
Price
Color
Size
Quantity
minimum quantity: x available in bundles of: x Product ordered in bundles.
Shipping
bucketsofink has a highly developed production and shipping system and we make every effort to ship your order in a fast and effecient manner.


