ER-VI-78-480-Infrared Conveyor Dryers-EconoRed II, III & VI [Add-On Cubes]-EconoRed-VI-78, Cube 400V/480V, 46,800w. Adds 9' (274 cm) of heat. 400V/480V - 3 phase only. Must add 18' belt (04-06-201)

EconoRed II, III & VI [Add-On Cubes] (includes: chamber, conveyor & 2 leg assemblies) (440-480V upgrade $800)

BROCHURE & SPECIFICATIONS

EconoRed VI dryers are offered in 30, 54 and 78 in. (76, 137 and 198 cm) belt widths to cure standard as well as oversized garments or flat goods screen-printed with plastisol, water-based inks or discharge, as well as DTF adhesives. Fully expandable, these dryers can grow as your needs grow.

Model ER-VI-30, with 30 in. (76 cm) wide belt and six 24 in. (61 cm) wide heaters (total 15,600 watts) cures up to 900 plastisol-printed garments/h placed in a single row, or 300 garments/h screen-printed with water-based ink or discharge.

Model ER-VI-54, with 54 in. (137 cm) wide belt and six 48 in. (122 cm) heaters (total 31,200 watts) cures up to 1,800 plastisol-printed garments/h placed in two rows, or 600 garments/h screen-printed with water-based ink or discharge.

Model ER-VI-78, with 78 in. (198 cm) wide belt and six 72 in. (183 cm) heaters (total 46,800 watts) cures up to 2,700 plastisol-printed garments/h placed in three rows, or 900 garments/h screen-printed with water-based ink or discharge.

All models include a digital belt speed display and a belt tracking system for increased belt life. The digital PID temperature controller is accurate to +/- 1°F (+/-0.5°C), allowing the operator to fine-tune or accurately repeat drying results at any future time.

HEAVY DUTY
-"X-Series" Conveyor Belt Tracking System

ADJUSTABLE
-Damper control knob modifies exhausted air flow from 100% to 10% to optimize curing of garments, transfer films and DTF adhesives

PRECISE
-Digital belt speed display for more accurate control

FOCUSED
-Infrared Focusing System allows 2 - 7 in. (5 - 17.7 cm) belt-to-heater height adjustment to accommodate hats or bulky garments, and can be customized to provide additional heater clearance.

ACCURATE
-Digital PID with fuzzy logic — industry's most advanced

CONSISTENT
-Heavy duty DC belt speed motor with digital voltage display

INNOVATIVE
-Engineered to be shorter and smaller with high heat and production

EXPANDABLE
-Add heat chambers and belt extensions

OPTIONS

• Add heating chambers @ 36 in. (91 cm) or 54 in. (137 cm) long
• Belt extensions, front or rear
• 3 Phase and 208, 380, 480 voltages
• Exhaust hood for extra fume extraction
• Hat support rail
• Locking casters for mobility
• Retrofit kits are available for upgrading existing EconoRed dryers with the adjustable exhaust damper.

ER-VI-78-480 questions

Can Buckets of Ink ship the ER-VI-78-480 to me?
Yes. It ships from Vastex or our Tempe, AZ warehouse; local pickup and Phoenix-metro delivery are available.

Will this dryer cure DTF adhesive powder?
Yes - Vastex rates its LittleRed, EconoRed and BigRed dryers for plastisol, water-based, discharge and DTF adhesives. Add the exhaust hood when curing DTF to reduce fumes.

Can I see Vastex equipment in person?
Yes - call ahead for our Tempe, AZ showroom at 906 S Priest Dr, Suite 101. Buckets of Ink is an authorized Vastex dealer.

Setup tips

• Have an electrician confirm voltage, phase and breaker size before delivery (use the hook-up worksheet below).
• Vent the dryer outside; add the exhaust hood when curing DTF adhesives.
• Set heater height 2-4 in. above the garment; raise it for hoodies and hats.
• Check cure with a heat gun or temp strip: most plastisol cures at 320°F through the whole ink film.

Quick troubleshooting

• Ink washes out (under-cured): slow the belt or lower the heaters and re-check temperature at the ink surface.
• Scorching or dye migration: raise the heaters or speed up the belt; try a low-cure ink on polyester.